Waterfowl hunting supplies, Hunting Store, Buy hunting supplies online, Duck hunting, Michigan duck hunting supplies, duck hunting Michigan
duck calls, decoys, duck decoys, duckhunting, hunting gifts, outdoor gifts, waterfowl, outfitters, hunting, outfitter, goose hunting, Michigan waterfowl supplies, Michigan hunting store


Knutson's Live Bait







Rigging Supplies - Anchor Molds

#1890
Magnum Melter

Ladle pouring can be faster and better than bottom pouring for sinker molds, as well as some jig and lure molds. At last there is an economical high capacity dip out melter available – the 20 pound capacity Magnum Melter. It utilizes the proven high-efficiency design to raise lead to temperature in about 20 minutes from a cold start, holds twenty pounds of lead, and has a calibrated thermostat to maintain proper temperature. The 4" x 4" I.D. carbon steel pot is large enough to work well with the large No. 1905 Cast Iron Ladle. 700 Watts, 110 Volt AC.

Price- $76.99 each

Model- 1890
Magnum Melter
Price- $76.99 each


#1894 Lee Pro 4-20 Lead Melter
An affordable large capacity melter that holds 20 pounds of lead in a 4" x 4" I.D. carbon steel pot. Features four inches of clearance beneath the spout, a new micro adjustable flow control valve, and an adjustable mold guide. It uses the patented Lee high-efficiency design with a dependable remote sensing thermostat. The flow valve can be adjusted to pour sinkers of up to two and three ounces quickly and without wrinkles. Note: The position of the pour spout underneath this furnace does not make it well suited for bottom pouring spinner jig molds or other molds that require wires to protrude above. 700 watts, 110 Volt, adjustable heat control, and guaranteed by the manufacturer, for two (2) years.

Price- $96.99 Each

Model #1894
Lee Pro 4-20 Lead Melter
Price- $96.99 Each


Model- 1892
HOT POT 2 LEAD MELTER
This "electric ladle" has an externally mounted heating element to greatly extend element life. This unit both melts and pours lead. With its 4 LB lead capacity, heat resistant
plastic handle, metal stand, and three foot cord. 500 Watts, by Palmer  Mfg.

Price- $39.99 each

Model- 1901
PRODUCTION POT IV
This efficient bottom pouring furnace holds approximately 10 lbs. of lead.  With 4" of clearance under the spout.  With its 500 watts of power it is a
great help when melting lead for your decoy anchors.

Price- $69.99 each

Model- 1892
HOT POT 2 LEAD MELTER
Price- $39.99 each
Model- 1901
PRODUCTION POT IV
Price- $69.99 each


#1199 6 oz. Pyramid Decoy Anchor Mold
These decoy anchors have been an old standard of duck hunters everywhere for years. The pyramid shape is favored in hard bottom locations where it has less tendency to roll with a current.

Price- $40.99 Each

Model # 1199
6 oz Pyramid Decoy Anchor Mold
Price- $40.99 Each


#1897 Cast Iron Ingot Mold
This four-cavity cast iron pan is useful when melting down scrap lead, blending alloys or emptying melting furnaces. Forms easy-to-use, one-pound stackable lead ingots.

Price- $29.99 each

Model # 1897
Cast Iron Ingot Mold
Price- $29.99 each


Model- DOIT-3254
4 oz. Egg Sinker Mold

This high quality lead anchor mold has 3 cavities that make 4 oz. Egg Sinkers. By making your own anchors you can save a lot of money and at the same time recycle that old lead that you have lying around.
The Do-It Egg Sinker Mold includes a Pull Pin, model #1917, to easily make a hole through the lead.

Price- $46.99 each

Model- DOIT-3378
10/12 oz. Egg Sinker Mold

This high quality lead anchor mold has 2 cavities that make a 10 oz. and a 12 oz. Egg Sinker. By making your own anchors you can save a lot of money and at the same time recycle that old lead that you have lying around. The Do-It Egg Sinker Mold includes a Pull Pin, model #1928, to easily make a hole through the lead.

Price- $46.99 each

Model- DOIT-3254
4 oz. Egg Sinker Mold
Price- $46.99 each
Model- DOIT-3378
10/12 oz. Egg Sinker Mold
Price- $46.99 each


Model- DOIT-3380
14/16 oz. Egg Sinker Mold

This high quality lead anchor mold has 2 cavities that make a 14 oz. and a 16 oz. Egg Sinker. By making your own anchors you can save a lot of money and at the same time recycle that old lead that you have lying around. The Do-It Egg Sinker Mold includes a Pull Pin, model #1928, to easily make a hole through the lead.

Price- $46.99 each

Model- MDA-3-456
3 CAVITY 4 OZ, 5 OZ, 6 OZ MUSHROOM ANCHOR MOLD

This high quality lead anchor mold makes 3 different sizes of mushroom anchors.  This mold produces 4 ounce, 5 ounce and 6 ounce mushroom anchors.   By making your own anchors you can save a lot of money and at the same
time recycle that old lead that you have lying around.

Price- $40.99 each

Model- DOIT-3380
14/16 oz. Egg Sinker Mold
Price- $46.99 each
Model- MDA-3-456
4, 5, 6 OZ MUSHROOM ANCHOR MOLD
Price- $40.99 each


Model- MDA-2-8
8 OZ  MUSHROOM ANCHOR MOLD

This lead anchor mold makes two 8 ounce mushroom anchors at the same time.  This size anchor is a good size
for those larger decoys such as magnum ducks and most goose decoys.

Price- $40.99 each

Model- DOIT-1928
Pull Pin for 10/12 oz. or 14/16 oz. Egg Sinker Mold

This Do-It Pull Pin is used to easily make the hole through your larger Egg Sinkers.

Price- $5.99 each

Model- MDA-2-8
8 OZ  MUSHROOM ANCHOR MOLD
Price- $40.99 each
Model- DOIT-1928
Pull Pin for 10/12 oz. or 14/16 oz. Egg Sinker Mold
Price- $5.99 each


Model- 1885
STRAP ANCHOR MOLD

This one- piece, three-cavity mold makes either strap type duck decoy anchors or lead ingots.  There are 2 different levels of fill in each cavity.  When making strap anchors, use soft lead and fill the cavity only to the first level to make 6
ounce anchors, fill the cavity to the second level to make lead ingots up to 16 ounces.

Price- $17.99 each

Li'l Mac Molds
Li'l Mac A-Series Molds are self-locking, no vise or other clamps needed. Clip lock comes with each mold! Free standing, no stand or bracket needed. Li'l Mac molds come equipped with large hinges to provide easy opening, and machined surfaces to eliminate flash. These molds require little to no clean-up or trimming. This mold self stores string and will fit over decoy's head or you can cut and bend around the neck.

A3100 9.5 oz Anchor Mold
A3110 12 oz Anchor Mold
Price- $84.99 each

Model- 1885
STRAP ANCHOR MOLD
Price- $17.99 each

Quantity:


Model- DOIT-3483
J-Style (Keel Hook) Decoy Weight Mold

This weight will save you time, eliminate decoy bag tangles and prevent decoy paint wear. It hooks to the decoy's keel and is easily removed even while wearing gloves on those cold, dark mornings. Decoys that are easy out + easy in = more time to hunt. This high quality lead anchor mold has 3 cavities that make a 4 oz., 6 oz. and 8 oz. J-Style Anchors.

Price- $76.99 each

Model- DOIT-1917
Pull Pin for 4 oz. Egg Sinker Mold

This Do-It Pull Pin is used to easily make the hole through your 4 oz. Egg Sinkers.

Price- $5.99 each

Model- DOIT-3483
J-Style (Keel Hook) Decoy Weight Mold
Price- $76.99 each
Model- DOIT-1917
Pull Pin for 4 oz. Egg Sinker Mold
Price- $5.99 each


DOIT-5473 Keel Weight Tubing
Ten inch neoprene tubing used with keel-hook decoy weights. Complete with 2 plastic o-rings and c-style hog rings. Come packaged in 12 per pack.

Price- $18.99 per pack
Model DOIT-5473
Keel Weight Tubing
Price- $18.99 per pack


DOIT-5470 C-Ring
C-style hog rings used with keel-hook decoy weights. Come packaged in 25 per pack.

Price- $1.99 per pack
Model DOIT-5470
C-Ring
Price- $1.99 per pack


DOIT-5471 Rubber Tubing
Ten inch neoprene tubing can be used with keel-hook decoy weights. Come packaged in 12 per pack.

Price- $10.99 per pack
Model DOIT-5471
Rubber Tubing
Price- $10.99 per pack

DOIT-5472 Plastic O-Rings
One inch plastic O-Rings that can be used with keel-hook decoy weights. Come packaged 25 per pack.

Price- $3.89 per pack
Model DOIT-5472
Plastic O-Rings
Price- $3.89 per pack




#1886 Large Ladle
With the capability of holding 8.5 lbs. of lead, this ladle is designed to be utilized for our Downrigger molds. 5" diameter. Steel construction. Right and left pouring lips. 18" handle.

Price- $31.99 each

#1887 Large Cast Iron Pot
Designed to work in conjunction with our Large Ladle, this large pot will hold 50 lbs. of lead. 8" diameter, 4" depth. Wire handle, pouring lip and tipping handle. Cast iron construction.

Price- $50.99 each

Model- 1886
Large Ladle
Price- $31.99 each
Model- 1887
Large Cast Iron Pot
Price- $50.99 each


Model- 1905
CAST IRON LADLE

This cast iron ladle has a 3" diameter cup to hold up to 1
-1/2 lbs. of lead and is designed to pour larger cavity molds. You can pour lead out of either side for ease of pouring.

Price- $19.99 each

Model- 1904
CAST IRON POT

This cast iron pot has a large 20 LB capacity.  this 5" diameter pot holds twice
as much metal as the average bullet pot.  This is a great compliment item to the cast iron ladle # 1905.

Price- $23.99 each

Model- 1905
CAST IRON LADLE
Price- $19.99 each
Model- 1904
CAST IRON POT
Price- $23.99 each


#2269 Clean Cast Fluxing Compound
Lead fluxing compound will remove sand, dirt, sludge, oxidation and other impurities in your lead which will result in better castings.

Price- $15.99 Each
Model #2269
Clean Cast Fluxing Compound
Price- $15.99 Each


#2270 Casting Release Spray
Release spray will apply a micon-sized graphite coating to the surface of your mold. Even though Do-It Molds do not require a release agent, this product will help the release of the castings on older or modified molds.

Price- $12.99 Each

Special Shipping Notice: This product contains flammable materials and may be shipped only via ground service within the continental United States.
Model #2270
Casting Release Spray
Price- $12.99 Each

This site was created by: Up North Outdoors Inc.
Interested in: Advertising with UpNorthOutdoors.com Copyright®